Document	mce_p1p51fe30-001Q
Descrizion	Electric connections manual for application P1P51FE30-001
Drawn up	Michele Sandri
Approved	Gabriele Bazzi
Link	https://www.qem.eu/doku/doku.php/en/strumenti/qmoveplus/j1p51/p1p51fe30-001/mce_p1p51fe30-001
Language	English
Document Release	Description	Notes	Date
01	New manual		10/06/2015

<wrap lo> All rights reserved on this manual. No part of this document can be copied or reproduced in any form without prior written authorisation. QEM does not insure or guarantee its contents and explicitly declines all liability related to the guarantee of its suitability for any purpose. The information in this document can be changed without notice. QEM shall not be held liable for any error or omission in this document. QEM® is a registered trademark.

• NO = Normally Opened
• NC = Normally Closed
• PR = Programmable
• I = Impulsive
• C = Continuous

NAME	DESCRIPTION	LOGIC			TERMINAL		HARDWARE
I01	FC Y maximum	NO	C			CN11.4	J1-P51
I02	FC Y minimum	NO	C			CN11.5
I03	Motor driver disk fault	NO	C			CN11.6
I04	Disc motor running	NC	C			CN11.7
I05	Disc motor in stop	NC	C			CN11.8
I06	Auxiliary OK	NC	C			CN11.9
I07	Air disc motor and thermal OK	NC	C			CN11.10
I08	Thermal engine oil pump OK	NC	C			CN11.11
I09	Barrier closed	NC	C			CN12.4
I10	Pressure water present	NC	C			CN12.5
I11	Enabling tilting bench	NC	C			CN12.6
I12	Motor Driver X fault	NO	C			CN12.7
I13	Y motor driver in fault	NO	C			CN12.8
I14	Driver V engine in fault	NO	C			CN12.9
I15	Driver Motor Z in fault	NO	C			CN12.10
I16	Motor Driver C in fault	NO	C			CN12.11
I17	FC X maximum	NO	C			CN13.4
I18	FC X minimum	NO	C			CN13.5
I19	FC Z maximum	NO	C			CN13.6
I20	FC Z minimum	NO	C			CN13.7
I21	FC C maximum	NO	C			CN13.8
I22	FC C minimum	NO	C			CN13.9
I23	Low oil level	NO	C			CN13.10
I24	RESET button automatic cycle	NC	I			CN13.11
I25	STOP automatic cycle (HOLD)	NO	C			CN14.4
I26	Jog button forward X	NC	I			CN14.5
I27	Button jog back X	NC	I			CN14.6
I28	Y jog button forward	NC	I			CN14.7
I29	Button jog back Y	NC	I			CN14.8
I30	Phase A Flyer					CN14.9
I31	Selector speed spindle blade	NC	C			CN14.10
I32	Selector tool spindle speed	NC	C			CN14.11

• I = Impulsive
• C = Continuous

NAME	DESCRIPTION	LOGIC		TERMINAL		HARDWARE
O01	Enabling spindle	C			CN7.2	J1-P51
O02	Activation by-pass safety barriers	C			CN7.3
O03	Turning oil pump for tilting bench	C			CN7.5
O04	Enabling EV water cooling	C			CN7.6
O05	Laser activation	C			CN7.8
O06	Alarm in progress	C			CN7.9
O07	Lamp presence alarm	I/C			CN7.10
O08	Enabling EV climb bench	C			CN7.11
O09	Enabling EV descent bench	C			CN8.2
O10	Enable drive axis X	C			CN8.3
O11	Enable drive axis Y	C			CN8.5
O12	Enable drive axis V	C			CN8.6
O13	Enable drive axis Z	C			CN8.8
O14	Enable drive axis C	C			CN8.9
O15	Signaling axis in motion	C			CN8.10
O16	Reset driver	I/C			CN8.11
O17	Selection rotating disk (OFF) or cutter (ON)	I/C			CN9.2
O18	Activation lubrication	C			CN9.3
O19	reserve				CN9.5
O20	reserve				CN9.6
O21	reserve				CN9.8
O22	reserve				CN9.9
O23	reserve				CN9.10
O24	reserve				CN9.11
O25	reserve				CN10.2
O26	reserve				CN10.3
O27	reserve				CN10.5
O28	reserve				CN10.6
O29	reserve				CN10.8
O30	reserve				CN10.9
O31	reserve				CN10.10
O32	reserve				CN10.11